HC008, DC12V,Max 2048 pixels, Pixel Module Full Color Controller

Special Price $45.50 Regular Price $50.00
In stock
  • Buy 5 for $39.50 each and save 13%
  • Buy 10 for $35.90 each and save 21%
  • Buy 30 for $29.04 each and save 36%

Product Specification

Type: Dream Color Remote Controller

Standards And Certifications: CE/FCC/ROHS Compliant

Warranty: 3 years

Craft materials: ABS/Brand new and high quality

Working temperature: -20~+60°C

Supply voltage: DC 12V

Output: two SPI signal.

Program Effects(pre-loaded): 133

Maximum control points: 4outputs, each port can control 1,024pixel max, totally can control 4,096 pixels max.

Controlled IC Type: Such as theTM1803, TM1804, TM1809, UCS1903etc. (specify the required model on orders)
Length setup function: yes

Consume power: 2W

Moudle QTY: 133 programs to choose

Size: 9.5cm(3.74inch) x 5.8cm(2.28inch) x 2.6cm(1.02inch)


Wireless Synchronous LED Controller HC008 is suit for UCS1903, WS2811, TM1812, TM1804 etc) output applications, which drive LED directly. It is widely used in advertising, Club, stage sets, home decorations, etc. It has many advantages such as low price, easy connection and simple to use. It has a memory function. Meanwhile, you could adjust brightness, static color choices and various dynamic changes in lighting effects through wireless remote control. It can also be used as a synchronous controller. That is to say you can synchronously control number of decoders and LED lights. You don’t need to take much time to learn how to program effects because more than 100 program effects are pre-loaded.

Maximum control points:1024(Low-speed) points,2048(High-speed) points.

The distance of the first point to controller:Low-speed mode<40m;High-speed mode<20m.(when more than 5 meters,you should use the shielded to connect.)If it is more than the distance,you must add a"TTL level to 485 level" module.


Function of button(controller is in playing state)

(1).ON/OFF:ON/OFF button,it can open or close output.



(4).Mode/Speed:Mode adjustable/speed adjustable function switch(The dirst LED displays H for model adjustable,shows S for the speed adjustable.)

Note:After powering,the red light would bright.And each press, the green light flash one time.

Connect the load well wire at first, following by the power wire;

Please ensure short circuit can not occur between connecting wire before you turn on the power.

Then set the steps as follows.

Press the "On / off" button to take the controller off before setting the menu

Press the "up", "down" button one time at the time, and LED would be bright at this moment.

Then press the "Mode / Speed" button to get into the menu settings screen.

The first setting screen is for "High-speed, low-speed settings", and the LED would display "S-HI" or "S-LO".

Then press the "up" and "down" button to select the mode. (If the IC on the light bar is high-speed mode, you should choose "S-HI", and choose "S-HI" when low-speed.) The factory default is for the high-speed mode.

Continue to press the "Mode / Speed" button to enter the second screen-"Control points setting".

The LED display 4-digit is for the number of control points. To plus or minus the number by pressing the "up" and "down" button (Long pressing can adjust quickly). The factory default is for 50.

After setting well, press the "On / off" button to save and exit

Typical application

Application circuit 1:

Application circuit 2: Multi-motor synchronization function

(Each controller can separate the power supply also can share power supply)

Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account
We found other products you might like!
© 2009-2024 LightingNext Ltd. All Rights Reserved.